Skip to content

Food Machinery Mesh & Screens · FDA 21 CFR / EU 1935/2004 food contact

4 Mesh Food Dehydrator Stainless Mesh Tray Specifications

A stack of stainless steel mesh dehydrator trays with apple slices and jerky in a food dehydrator on a kitchen counter

Specification data for 4 mesh food dehydrator stainless mesh tray to FDA 21 CFR / EU 1935/2004 food contact: aperture and micron rating, standard and alternative wire diameters, open area, weight per square metre, and the applications this fineness is commonly used for.

4 Mesh Specification Row (FDA 21 CFR / EU 1935/2004 food contact)

Mesh countWire diameter (mm)Aperture (mm)Micron rating (u00b5m)Open area (%)Tray (mm)
4-Mesh0.9005.450545072.0400 u00d7 400

4 Mesh to Micron & Aperture

Openings per inch4
Aperture (opening width)5.35 mm
Micron rating5350 µm
Standard wire diameter1 mm
Open area71 %

Aperture = (25.4 mm ÷ mesh count) − wire diameter. The micron rating equals the aperture in micrometres; actual retention also depends on particle shape and cake formation.

Wire Diameter Options at 4 Mesh

OptionWire diaApertureMicronOpen areaWeight (SS)
Heavy wire1.300 mm5.050 mm5050 µm63.2 %3.48 kg/m²
Standard wire1.000 mm5.350 mm5350 µm71.0 %2.06 kg/m²
Fine wire0.750 mm5.600 mm5600 µm77.8 %1.16 kg/m²

Heavier wire adds strength and abrasion life but closes the aperture; finer wire opens the aperture and raises throughput at the cost of durability. Specify mesh count AND wire diameter to fix the aperture unambiguously.

Open Area & Flow at 4 Mesh

The standard 4 mesh weave presents an open area of about 71%. At this count the mesh presents little flow resistance; selection is normally driven by particle retention and mechanical strength rather than pressure drop.

4 Mesh Cloth Weight

Standard 4 mesh stainless cloth weighs approximately 2.06 kg/m² (density 7.93 g/cm³ basis; brass and copper weave roughly 10% heavier, aluminum about one third). Use this figure for roll handling and freight estimation.

Typical Applications for 4 Mesh Food Dehydrator Stainless Mesh Tray

4 mesh food dehydrator stainless mesh tray is commonly specified for coarse screening and grading, safety guarding, animal enclosures, plaster and render reinforcement, and support layers behind finer filter cloth.

Plain, Twill or Dutch Weave at This Rating?

Plain square weave is the standard at this count: every opening is a true square of the stated aperture, retention is absolute for hard spherical particles, and the cloth is easy to clean.

What Food Dehydrator Stainless Mesh Tray Does

Drying fruit, vegetables, jerky, herbs and pet treats on stainless mesh trays that let warm air pass evenly through every layer of a dehydrator or drying room.

Fitting & Care

  • Space pieces so air can pass between them.
  • Wash trays in hot soapy water or the dishwasher after use.
Mesh count to micron conversion chart
Mesh count to aperture and micron rating. Confirm the exact figure against the specification table below — wire diameter, not mesh count alone, sets the aperture.

Technical Drawing

Customize the parameters below — every spec field is editable, and the drawing redraws to match the values you choose. Changing the size will snap the other fields to that size's standard values; you can then override any individual value.

Sends the selected values to the quote form below.

Request a Quote

Adjust the parameters in the drawing above and click "Request this configuration" to send the exact specification straight to this form.

Request a Quotation

Specification
Business Information

Dimensions & Specifications (FDA 21 CFR / EU 1935/2004 food contact)

Mesh countWire diameter (mm)Aperture (mm)Micron rating (u00b5m)Open area (%)Tray (mm)
4-Mesh0.9005.450545072.0400 u00d7 400
8-Mesh0.6002.575257565.8400 u00d7 400
14-Mesh0.4001.414141460.4600 u00d7 400
20-Mesh0.3000.97097058.3600 u00d7 400

Frequently Asked Questions

Stainless or plastic dehydrator trays?

Stainless is heat-safe, durable and does not absorb odors.

What mesh for drying herbs?

About 14–20 mesh.

How do I request a quotation?

Use the technical drawing on this page to pick the exact specification, then submit it with the quote form. We respond within one business day.